AS9100 Rev C, ISO 9001:2008,
ISO 14001:2004 and OHSAS 18001:2007
Filter and Ferrite Products
Move cursor over the links to see product images
Click the links for more information
The series FBI full waveguide band isolator is a Faraday rotation ferrite device. This isolator is offered from 18 to 220 GHz in ten waveguide bands. The isolator consists of a section of waveguide containing low loss ferrite material and impedance matching elements. The isolator has a maximum insertion loss of 1.5 dB in K-Band and 4.5 dB in G-Band. The corresponding isolation is 25 and 20 dB
Click
Here to download the FBI product datasheet
Electrical Specifications
| Model | FBI-42 | FBI-28 | FBI-22 | FBI-19 | FBI-15 |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 |
Q 33-50 |
U 40-60 |
V 50-75 |
| Insertion loss (dB) (max) | 1.5 | 1.5 | 1.5 | 1.7 | 1.8 |
| Insertion loss (dB) (typ) | 1.0 | 1.0 | 1.1 | 1.2 | 1.6 |
| Isolation (dB) (min) | 25 | 27 | 27 | 27 | 27 |
| Input/Output VSWR (max) | 1.4:1 | 1.4:1 | 1.4:1 | 1.4:1 | 1.4:1 |
| Power rating (W) (max) | 3 | 2.5 | 2 | 1.5 | 1.5 |
| Model | FBI-12 | FBI-10 | FBI-08 | FBI-06 | FBI-05 |
| Frequency band and range (GHz) | E 60-90 |
W 75-110 |
F 90-140 |
D 110-170 |
G 140-220 (Note1) |
| Insertion loss (dB) (max) | 2 | 2.5 | 2.8 | 3.2 | 4.0 |
| Insertion loss (dB) (typ) | 1.7 | 2.0 | 2.2 | 2.9 | 3.5 |
| Isolation (dB) (min) | 27 | 27 | 20 | 20 | 20 |
| Input/Output VSWR (max) | 1.4:1 | 1.4:1 | 1.4:1 | 1.4:1 | 1.4:1 |
| Power rating (W) (max) | 1 | 1 | 0.75 | 0.75 | 0.75 |
1) The performance of G-Band (WR-05) isolators is measured at selected frequencies within the band. Performance specifications given above are typical values measured in the frequency band.
The series JFD junction ferrite isolator and circulator covers the frequency range from 18 to 100 GHz in seven waveguide bands. The isolator and circulator provide high isolation and low insertion in a relatively small package. These units are available in two configurations: single-junction and triple-junction.
Click
Here to download the JFD product datasheet
Electrical Specifications
| Model | JFD-42 | JFD-28 | JFD-22 | JFD-19 | JFD-15 | JFD-12 | JFD-10 |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 |
Q 33-50 |
U 40-60 |
V 50-75 |
E 60-90 |
W 75-100 |
| Single Junction Units (Partial band) | |||||||
| Bandwidth (GHz) (max) (Note 2) | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 |
| Isolation (dB) (min) | 20 | 20 | 20 | 20 | 20 | 20 | 20 |
| Insertion loss (dB) (max) | 0.3 | 0.5 | 0.5 | 0.6 | 0.7 | 0.8 | 0.8 |
| VSWR (max) | 1.2:1 | 1.2:1 | 1.2:1 | 1.3:1 | 1.3:1 | 1.3:1 | 1.3:1 |
| Power rating (W) (max) (Note 1) | 10 | 10 | 8 | 7 | 6 | 5 | 5 |
| Triple Junction Circulators | |||||||
| Bandwidth (GHz) (max) (Note 2) | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 | 2.0(Note 3) |
| Isolation (dB) (min, ports 2 to 1 and 3 to 2) | -- | 35 | 35 | 35 | 35 | 35 | 35 |
| Insertion loss (dB)(max, ports 1 to 2 and 2 to 3)) | -- | 0.8 | 1.0 | 1.2 | 1.4 | 1.6 | 1.8 |
| VSWR (max) | -- | 1.2:1 | 1.2:1 | 1.3:1 | 1.3:1 | 1.3:1 | 1.3:1 |
| Power rating (W) (max) (Note 1) | -- | 10 | 8 | 7 | 6 | 5 | 5 |
| Triple Junction Isolators | |||||||
| Bandwidth (GHz) (max) (Note 2) | --- | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 | 2.0 (Note 3) |
| Isolation (dB) (min) | --- | 50 | 50 | 50 | 50 | 50 | 50 |
| Insertion loss (dB) (max) | --- | 1.2 | 1.3 | 1.6 | 1.9 | 2.2 | 2.5 |
| VSWR (max) | --- | 1.2:1 | 1.2:1 | 1.2:1 | 1.3:1 | 1.3:1 | 1.3:1 |
| Power rating (W) (max)(Note 1) | --- | 10 | 8 | 7 | 6 | 5 | 5 |
1) Load VSWR 3:1 or better.
2) Maximum bandwidth offered for the standard products. Please specify bandwidth requirement.
3) 1 GHz bandwidth for frequencies above 96 GHz.
The series WBI wide band isolators provide an ideal solution for applications in broadband instruments and systems, swept frequency applications and cryogenically cooled radio telescopes. These isolators feature low insertion loss and high isolation in a compact size. They are also ideal for applications where space is at a premium.
Click
Here to download the WBI product datasheet
Electrical Specifications (Note1)
| Model | WBI-10 |
| Operational frequency range (GHz) | 82-110 |
| Insertion loss (dB) (max) (Note2) | 1.3 |
| Insertion loss at 80K (dB) (typ) | 0.6 |
| Isolation (dB) (min) (Note2) | 20 |
| VSWR (max) (Note2) | 1.5:1 |
1) At ambient temperature only.
2) Includes mismatch due to port configuration.
Note: Can be tuned for cryogenic operation, but tested at ambient
temperatures.
Millitech series HPC junction ferrite devices (circulators) cover the frequency range from 18 to 110 GHz. The circulator is a four-port, differential phase shift device which can be configured as an isolator by terminating two of the ports. The high isolation, low insertion loss, low VSWR (high return loss), and high power handling typical of these ferrite devices make them ideal for use with frequency sources, amplifiers, and receivers.
Click
Here to download the HPC product datasheet
Electrical Specifications
| Model Number | HPC-42 | HPC-28 | HPC-22 | HPC-19 | HPC-15 | HPC-12 | HPC-10 |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 |
Q 33-50 |
U 40-60 |
V 50-75 |
E 60-90 |
W 75-110 |
| Bandwidth (Note 1) | 10% | 10% | 10% | 10% | 10% | 10% | 10% |
| Isolation (dB) (typ) (Note 2) | 20 | 20 | 20 | 20 | 20 | 20 | 20 |
| Insertion loss (dB) (typical, mid-band) | 0.6 | 0.8 | 0.9 | 1.0 | 1.1 | 1.2 | 1.3 |
| VSWR (typ) | 1.3:1 | 1.3:1 | 1.3:1 | 1.3:1 | 1.3:1 | 1.3:1 | 1.3:1 |
| Average Power Rating (W) (Note 3) | 200 | 200 | 200 | 200 | 200 | 200 | 200 |
| Peak Power Rating @ Sea Level (W) | TBA | TBA | TBA | TBA | TBA | TBA | 2000 |
1) Maximum bandwidth offered for the standard products. Please specify bandwidth requirement.
2) Measured Port 2 → Port 1
3) Load VSWR 3:1 or better. Please specify power requirements at time of order.
The series FLP low pass filter provides high rejection and excellent selectivity for frequencies above the corner frequency. The filter covers 18 to 110 GHz in seven waveguide bands. The insertion loss is 1 dB in K-Band and increases to 1.6 dB (max) in W-Band. The waveguide cut-off frequency determines the rejection at the lower band edge. This filter has a wide stopband, rejecting up to three times the highest passband frequency.
Click
Here to download the FLP product datasheet
Electrical Specifications
| Model | FLP-42 | FLP-28 | FLP-22 | FLP-19 | FLP-15 | FLP-12 | FLP-10 |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 | Q 33-50 |
U 40-60 |
V 50-75 |
E 60-90 |
W 75-110 |
| Insertion loss (dB) (max) | 1 | 1 | 1 | 1 | 1.2 | 1.4 | 1.6 |
| Upper band edge (fE) (typ) (corner frequency) (GHz) | 28.3 | 41.2 | 52 | 62 | 77 | 93 | 114 |
| Rejection band (fH to fU) (GHz) (typ) (Note 1) | 34-66 | 49-95 | 62-120 | 74-143 | 92-178 | 111-214 | 139-263 |
| Waveguide cutoff frequency (fC) (GHz) (Note 2) | 14.1 | 21.1 | 26.3 | 31.4 | 39.9 | 48.4 | 59.1 |
| Custom Products | |||||||
| Rejection range for high frequencies (fH to fU) (dB) | 22-55 | 25-50 | 25-45 | 25-40 | 25-40 | 25-40 | 25-40 |
1) Rejection band attenuation
(fH to fU): > 40 dB.
2) Frequencies below this waveguide cut-off frequency are significantly
attenuated. Typical rejection at 0.85 times cut-off frequency is
40 dB
Millitech series FIB iris bandpass filters have a narrow passband in the range of 1% to 15% of center frequency. These filters offer low insertion loss in the passband with a wide range of passband frequencies. Filters in this series are available from 18 to 220 GHz, and can handle up to 10 Watts. These filters also offer excellent rejection at high and low side rejection frequencies. Characteristics of the filter can be modified to suit specific rejection requirements.
Click Here to download the FIB product datasheet
Electrical Specifications
| Model | FIB-42 | FIB-28 | FIB-22 | FIB-19 | FIB-15 |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 |
Q 33-50 |
U 40-60 |
V 50-75 |
| Typical Passband IL (dB) | 0.25 | 0.25 | 0.3 | 0.35 | 0.35 |
| Maximum Passband IL (dB)(Note 1) | 0.4 | 0.4 | 0.5 | 0.55 | 0.55 |
| LRL @ FRL (Note 1) | > 50 | > 50 | > 50 | > 50 | > 50 |
| LRH @ FRH (Note 1) | 45 | 42 | 40 | 38 | 35 |
| Passband VSWR (Note 1) | 1.5:1 | 1.5:1 | 1.5:1 | 1.5:1 | 1.5:1 |
| Model | FIB-12 | FIB-10 | FIB-08 | FIB-06 | FIB-05 |
| Frequency band and range (GHz) | E 60-90 |
W 75-110 |
F 90-140 |
D 110-170 |
G 140-220 |
| Typical Passband IL (dB) | 0.45 | 0.6 | (Note 2) | (Note 2) | (Note 2) |
| Maximum Passband IL (dB) (Note 1) | 0.75 | 0.9 | (Note 2) | (Note 2) | (Note 2) |
| LRL @ FRL (Note 1) | > 50 | 50 | (Note 2) | (Note 2) | (Note 2) |
| LRH @ FRH (Note 1) | 35 | 30 | (Note 2) | (Note 2) | (Note 2) |
| Passband VSWR (Note 1) | 1.5:1 | 1.5:1 | (Note 2) | (Note 2) | (Note 2) |
1) Specifications are based upon a 6-section, 10% bandwidth filter. Measurements are typical.
2) Please consult Millitech for further information.
| Legend | |
| BW | Bandwidth |
| FC | Center Frequency |
| FRL | Low Side Rejection Frequency (FC – 1.5BW) |
| FRH | High Side Rejection Frequency (FC+ 1.5BW) |
| LRL | Attenuation at FRL |
| LRH | Attenuation at FRH |
| IL | Passband Insertion Loss |
The series FNP narrow bandpass filter has a passband bandwidth in the range of 2% to 5% of center frequency. The filter offers low insertion loss in the passband and a high degree of selectivity. For example, the typical insertion loss for a filter with 2% passband bandwidth in Ka-Band is 1.8 dB. Characteristics can be tailored to suit specific rejection requirements. The series FNP is available in eight waveguide bands from 18 to 140 GHz
Click Here to download
the FNP product datasheet
Electrical Specifications
| Model | FNP-42 | FNP-28 | FNP-22 | FNP-19 | |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 |
Q 33-50 |
U 40-60 |
|
| Insertion loss (dB) (max) (Note1) | 2% | 1.8 | 1.8 | 1.8 | 1.8 |
| 4% | 1.6 | 1.6 | 1.6 | 1.6 | |
| Low side rejection level (dB) (min) @ FRL (Note 2) | 40 | 40 | 40 | 40 | |
| High side rejection level (dB) (min) @ FRH (Note 2) | 30 | 30 | 30 | 30 | |
| Passband VSWR (typ) | 1.5:1 | 1.5:1 | 1.5:1 | 1.5:1 | |
| Model | FNP-15 | FNP-12 | FNP-10 | FNP-08 | |
| Frequency band and range (GHz) | V 50-75 |
E 60-90 |
W 75-110 |
F 90-140 |
|
| Insertion loss (dB) (max) (Note1) | 2% | 2 | 2 | 2.2 | (Note 3) |
| 4% | 1.8 | 1.8 | 2 | (Note 3) | |
| Low side rejection level (dB) (min) @ FRL (Note 2) | 40 | 40 | 40 | (Note 3) | |
| High side rejection level (dB) (min) @ FRH (Note 2) | 30 | 30 | 30 | (Note 3) | |
| Passband VSWR (typ) | 1.5:1 | 1.5:1 | 1.5:1 | (Note 3) | |
1) Data is based upon a 5-section
filter. Upper limit is ~ 6% bandwidth.
2) Standard rejection frequencies (FRL and FRH
) are calculated at center frequency ± (1.5 x bandwidth in GHz).
3) Please consult Millitech for further information. Note: Other
bandwidth percentages are available upon request. (See series FIB
for other bandwidth requirements and options)
The series FHP high pass filter is designed and constructed to provide a sharp skirt selectivity of low frequency with minimum insertion loss in the passband. The typical insertion loss is 0.7 dB in K-Band, and increases to about 1.5 dB in W-Band. The insertion loss is determined by the corner frequency and selectivity. This filter is available in eight waveguide bands from 18 to 140 GHz. The filter characteristics can be tailored to meet specific rejection requirements
Click Here to download
the FHP product datasheet
Electrical Specifications
| Model | FHP-42 | FHP-28 | FHP-22 | FHP-19 |
| Frequency band and range (GHz) | K 18-26.5 |
Ka 26.5-40 |
Q 33-50 |
U 40-60 |
| Range of cut-off frequency (band edge) (GHz) (Note 1) | 14-23 | 21-35 | 25-44 | 31-52 |
| Passband loss (dB) (max) (Note 2) | 0.7 | 1 | 1 | 1.2 |
| Rejection at 90% of cut-off frequency (dB) (typ) (Note 3) | 45 | 45 | 40 | 40 |
| Model | FHP-15 | FHP-12 | FHP-10 | FHP-08 |
| Frequency band and range (GHz) | V 50-75 |
E 60-90 |
W 75-110 |
F 90-140 |
| Range of cut-off frequency (band edge) (GHz) (Note 1) | 40-64 | 48-80 | 59-95 | 116-125 |
| Passband loss (dB) (max) (Note 2) | 1.3 | 1.3 | 1.5 | 2 |
| Rejection at 90% of cut-off frequency (dB) (typ) (Note 3) | 40 | 35 | 35 | 35 |
1) Cut-off frequency has 3 dB
loss (typical). Attenuation increases rapidly below this frequency.
2) Insertion loss passband is measured 4.0 GHz from the 3 dB cut-off
frequency.
3) Longer length is necessary to achieve greater attenuation. Please
consult Millitech for details.
Millitech will engineer custom variations of our standard MMW components, as well as, multi-component assemblies and solutions, with minimal non-recurring engineering (NRE) costs, to meet your specific requirements. Typically these modification are to meet one or more of the following requirements:
- Tuned for specific performance characteristics
- Extended operational temperatures
- MIL/Space qualified
- Hi-rel screening
- RoHS compliant
- ITAR compliant
Click Here for more information on Millitech's custom capabilities, components, assemblies and solutions.
Please contact your local sales representative or Millitech's sales team for information and quoting.
